New Thermostat Housing 11538635689 For BMW 228i 320i 328i 428i 528i xDrive 12-16

Description

11538648791 Thermostat Housing with Sensor Assembly Replacement for BMW E84 F10 F22 F30 F33 228i 320i 328i 428i 528i X1 X3 X4 X5 Z4 N20 2.0L Replace 11538635689 11538636595
🚘【Replace OE Numbers】Replaces the OE Number: 11538648791 11538635689 11537633476 11537588257 11537633477 11538636594 11538636595. Before ordering, please confirm whether the accessories are suitable for your vehicle.
🚘【Application】Engine Coolant Thermostat W/Housing Assembly: Compatible with BMW E84 F10 F22 F30 F33 228i 320i 328i 428i 528i X1 X3 X4 X5 Z4 N20 2.0L & more.Please see the below for full vehicle list.
🚘【High-Quality Materials】Use high-quality materials, improve performance, improve durability and tolerances. stable characteristics, high reliability, better help you repair leaking thermostat housings, and correct engine overheating caused by thermostat failure
🚘【Thermostat Features】Thermostat housing can reduce enginer wear, deposits and emissions by adjusting the amount of coolant into the radiator until the engine works in a suitable temperature.
TINCT
provides Engine and Cooling system accessories, among which the widely used Electronic Water Pump combines the advantages of self-priming pump and chemical pump. It is made of a variety of corrosion-resistant imported materials and has the properties of acid resistance, alkali resistance, corrosion resistance, etc; The self suction speed is extremely fast (about 1 second), the suction force is strong, and there is basically no noise. Exquisite workmanship, not only self-priming function, but also large flow (up to 25L/min), high pressure (up to 2.7kg), stable performance and Easy to Install.
FITS THE FOLLOWING VEHICLES
BMW 228i 2014-2016 xDrive 2015-2016
BMW 320i 2013-2016 xDrive 2013-2016
BMW 328i 2012-2016 GT xDrive 2014-2016 xDrive 2013-2016
BMW 428i 2014-2016 xDrive 2014-2016
BMW 528i 2012-2016 xDrive 2012-2016
BMW X1 2013-2015
BMW X3 2013-2016
BMW X4 2015-2016
BMW X5 2016-2016
BMW Z4 2012-2016
Fitment Information：
1、 Inspection before installation
Before installation, gently move the impeller by hand and rotate it for more than three times.
Check the harness plug for aging and poor contact. If the on-board harness plug needs to be replaced, please use the plug that meets the technical specifications of the original vehicle, and do not change the original harness definition
Note: The water pump cannot be dry friction, and it must not be powered on for dry operation without cooling and lubrication.
2、 Inspection after installation
Check whether there is coolant leakage at the interface.
Confirm that the plug buckle has been fastened.
Check whether the battery voltage is low.
Clear the fault code, run the engine for 15-20 minutes and observe whether the coolant temperature is normal and whether there is a high temperature alarm.
If the fault code "electronic water pump missing/missing" is reported during the initial installation, check the harness and plug for damage or poor contact.
Why Choose GOCPB?
Easy And Fast To Install
Our Replacements Can Be Easy To Install. Most Of Them Are Plug And Play. This Will Help Us to Save Much Time.
Excellent Performance And High Quality
Our product Made Of High Grade Material With High Level Of Craftsmanship. And We Have Strict Quality Check Before Sales.
Check whether your car has the following conditions：
1. Capacity of Cooling Cycle is weak.
2. There is Leakge of Water Pump Near Engine.
3. Water Pump Makes an Obviously Noise.